Celestin Apprentice 2

home *** CD-ROM | disk | FTP | other *** search

/ Celestin Apprentice 2 / Apprentice-Release2.iso / Source Code / Pascal / Snippets / SCSI / scsi.FAQ < prev next >

Wrap

Text File | 1993-06-09 | 63.0 KB | 1,478 lines | [TEXT/KAHL]

These files are available for FTP from ftp.cs.tulane.edu in the directory pub/scsi. Files are stored in file areas as they are found in the BBS with each area having a file named 'files.bbs' that tells what each file is. The file pub/scsi/index.Z list each file area, it's descriptions and it's files. Archive-name: scsi-faq Last-modified: 5/13/93 Version: @(#)scsi.faq 1.5 SCSI FAQ: Frequently Asked Questions for comp.periphs.scsi Table of contents: Is it possible for two computers to access the same SCSI disks? Where can I get SCSICNTL.EXE and other Adaptec files? What kinds of Optical Drives are available? Where can I get FTP/download SCSI documents? What is the telephone number of Archive Corporation? What is the telephone number for Quantum? What is the telephone number for Seagate? What is the telephone number and address of Conner Peripherals? What is the address and telephone number of Wangtek? What is the number for NCR? What is FAST SCSI? Where can I get SCSI documents? SCSI terminators should measure 136 ohms? What are the pinouts for SCSI connectors? What is the difference between SCSI-1 and SCSI-2? Is SYNCHRONOUS faster than ASYNCHRONOUS? Is the 53C90 Faster than spec? What are the jumpers on my Conner drive? What are the jumpers for my Wangtek 5150 drive? What is CAM? What is FPT (Termination)? What is Active Termination? Why Is Active Termination Better? ==== QUESTION: Is it possible for two computers to access the same SCSI disks? ANSWER From: burke@seachg.uucp (Michael Burke) ==== Yes, two (or more) systems can be on the same scsi bus as scsi disk and tape drives. As long as the scsi requirements are met - cable lengths, termination and type - the devices can share the scsi bus. The question should be - Are there any O/S' that will allow the sharing of file systems? It would not make sense for two hosts to go about treating shared disks as if they owned the device. Data would be destroyed pretty quickly. On the issue of tape devices, however, O/S' tend to give exclusive usage to an application. In this way, tape drives can be shared much more easily. Disks can be best shared by having two (or more) partitions on a disk. Each host "owning" it's own file system. ==== QUESTION: Where can I get SCSICNTL.EXE and other Adaptec files? ANSWER From: randy@psg.com (Randy Bush) and Timothy Hu timhu@ico.isc.com ==== New files from Roy as follows: ftp.psg.com:~/pub/adaptec/... -rw-rw-r-- 1 randy staff 110689 Feb 25 00:29 SCSICNTL.EXE.Z -rw-rw-r-- 1 randy staff 368640 Feb 25 00:27 adse.dd -rw-rw-r-- 1 randy staff 1959 Feb 25 00:25 adse.dd.readme -rw-rw-r-- 1 randy staff 17896 Feb 25 00:37 list -rw-rw-r-- 1 randy staff 99545 Feb 25 00:20 os2drv.zip -rw-rw-r-- 1 randy staff 70801 Feb 25 00:20 scsi_drv.Z -rw-rw-r-- 1 randy staff 66508 Feb 25 00:24 scsi_drv.readm -rw-rw-r-- 1 randy staff 118697 Feb 25 00:17 update.pkg.Z You can get the ASPI specs from Adaptec's Bulletin Board (408)945-7727. ==== QUESTION: What kinds of Optical Drives are available? ANSWER From: joungwoo@mensa.usc.edu (John Kim) ==== As I promised I am posting the summary of what I learned about 128mb optical drives through many kind replies and some effort on my part. The purpose of this informal survey was to aid people (starting from myself) in deciding on which 128mb optical drive to buy. When I posted my questions, it was done only on comp.mac.sys.hardware and forgot to do the same also on comp.arch.storage and comp.periphs.scsi where are less traffic than c.m.s.h. However, as a Macintosh owner myself, this survey was biased toward the Mac world and the mail order houses mentioned specializes in Mac-related products, although the below mentioned optical drives might be usable also with non-Mac platforms (Sun, NeXT, PC-compatibles). My questions were: o what kind of drive you bought from whom at what price o what drive mechanism (MOST, Epson, Fujitsu, Sony, ...) it uses o how fast it is in terms of average seek time & data transfer rate o how noisy the drive is o how large and heavy the drive is o what drive formatting program (eg, FWB or Silver Lining) you use what its goods/bads o the quality of the service of the seller (mail order company, retail store, etc.) Summary In general, these days, some magneto-optical (MO) drives seem to be almost as fast as (if not faster than) ordinary hard drives (HD). The access time of fastest 128MB MO drives (around 30ms) are slower than average HD's access time (15ms) but the transfer rate seems to be about the same (764KBytes/sec) or not much slower. The advantages of the MO drives over the HDs are that your storage space is almost limitless, expandable at a relatively cheap price ($40/120MB = 34 cents/MB) compared to $1/MB rate of HDs or that of SyQuest drives, and the life of the media is very long (they say it's 30 years or rewritable 100,000 times.) Fijitsu 128 REM Portable: At this moment, to my knowledge, 128 MByte optical drives based on Fujitsu mechanism seems to be the fastest, roughly having average seek time of 30ms and average transfer rate of 768KBytes/sec. These are the most recently introduced; when I called DGR Technology (800-235-9748) and MacProducts USA (800-MAC-USA1), both of which are in Texas, about a week ago they were taking orders for them at the lowest price ($999) (advertised in MacWorld April '93 issue). DGR didn't have them in stock yet and were expecting to have them in quantity in 10 weeks; MacProducts told me it will take 4 to 5 weeks before I get my order. Call them again now -- the situation may have improved. Another good thing about this Fujitsu drive is that it is more compact in size than previous 128mb optical drives, ie, "portable". I don't know how Fujitsu mechanism (FM) is different from Epson mechanism (EM) and how FM provides a similar performance at a cheaper price in a smaller frame. Maybe using split-head implementation to make the read-write head lighter? Could anybody post info on this? One person tells me that the eject mechanism is too strong, sometimes shooting the cartridge out making them land on the floor. He says Fujitsu told him that the FM's coming out in April will have gentler eject. Epson: The next fastest (or maybe just about the same speed) are Epson mechanism (EM) drives, having average access time of 34ms and transfer rate of 768KB/sec. These achieve faster speed compared to other old mechanisms by having a higher rpm (3600rpm vs. past 2400 rpm). MacDirect (selling products labelled NuDesign, 800-621-8467, in Chicago, IL) and DGR advertises to carry them and currently sells them at $1098 and these are available right now. Folks who used these seemed to be very satisfied. Slower ones: Other mechanisms (Sony, Panasonic, etc.) seem to have been dominating the optical drive market before FM and EM's advent. These have a typical access rate of ~45ms. I don't know if now there are new implementations that make them perform better then FM and EM. Maybe someone can tell us. My current plan is to wait several weeks and buy an FM ($999) when they get to have them in stock. Since MacDirect has been the leader in providing cheapest price they may start selling FMs at a competitive price soon. At the moment MacDirect doesn't seem to carry FMs yet. MacProducts USA is also a good place to look for good prices. These three places (DGR, Mac Products USA and MacDirect) are all advertised in MacWorld and MacUser. Noise Level: One thing to consider might be noise of the drive. Different mechanisms may have typical noise level, but one thing sure is that different resellers/companys' drive's noise level differs even for the same drive mechanism, eg, Sony. It looks like different casing produces different noise levels? (Could someone confirm/disconfirm this aspect?) Base on the report in Nov '92 issue of MacWorld, the noise level of MacDirect, MacProduct and DGR 128mb MO drives seem to be OK or quite quiet. This issue of MacWorld deals with removable media drives (optical drives of various capacity, SyQuest, Bernoulli and Flopticals) and you can get some idea on what the differences among different drive mechanisms are. Price of Media: Usual price per 128mb cartridge was $49 - $59. But ClubMac (800-258-2650, in California) was the cheapest place to buy -- $39/128mb cartridge. If you live in CA, due to sales tax, Computer Design & Graphic Systems (800-741-6227) (in Ft. Myers, Florida) might be your cheapest: $40. Formatting Software: Another thing to consider is what kind of media formatting software you will use. All companys (or mail order places) seemed to provide for free formatting program with their drives. I don't have the details on this. But an inefficient formatting can result in slow drive performance. The most popular one used to be FWB's Hard Disk Toolkit but Anubis (advertised to improve performance up to 35% [compared to what?]) is beginning to be used also. I don't know if all formatting program and the drive hardware allows to have read and write verify off but by having these turned off you can obtain significant speed boost at the risk of less secure data transfer. MacWorld's report warned that drives from some companys don't let you turn on/off the verify. In the worst case, some come with verify off and no option to toggle it back to ON. 256mb MO drives: In general these have better transfer rate (1.23MB/sec) and a little slower access time (35ms). I feel that this capacity will soon be the next standard. These drives are able to also read/write 128mb cartridges and 256mb will soon be new ANSI and ISO standard. I once heard from a saleperson at a mail order place that these are not reliable yet and he saw many they sold came back with complaints. This may be a non-general instance on a typical drive mechanism (seems to be MOST mechanism). Personally, I feel 128mb is accomodating enough for personal usage at home unless you are dealing with very large data files (eg, large graphic images). ==== QUESTION: Where can I get FTP/download SCSI documents? ANSWER From: news@mgse.UUCP (News Administator) ==== Last Changed: Thu Sep 24 23:31:09 CDT 1992 (New BBS Phone number) This is a periodic posting of information about some of the archives at ftp.cs.tulane.edu and the available files from the SCSI-BBS, including SCSI, ESDI, IPI, and Fiber Channel documents from the standards committees. These files are available for FTP from ftp.cs.tulane.edu in the directory pub/scsi. Files are stored in file areas as they are found in the BBS with each area having a file named 'files.bbs' that tells what each file is. The file pub/scsi/index.Z list each file area, it's descriptions and it's files. Thanks to John Lohmeyer of NCR, a majority of the SCSI related files from the SCSI BBS are now available for anonymous ftp. These files were sent to me by Mr. Lohmeyer at his expense so that more people would have access to them. The SCSI BBS (719-574-0424) contains a large amount of data relating to SCSI, and ESDI as well as SCSI-2, IPI, and Fiber Channel, as well as the last revision of the SCSI-1 standard before it went to publication by ANSI. Most of the files in the SCSI archive are either archived with the ZIP utility or compressed with the 'compress' program. Most of the text files are stored as Wordstar word processing files. PKzip for PC/MS-DOS is included in the archive to allow users to break up the .ZIP files, and the PC/MS-DOS binaries and .C source are also in the archive to convert the Wordstar documents to ASCII text. ==== QUESTION: What is the telephone number of Archive Corporation? ANSWER From: jdp@caleb.UUCP (Jim Pritchett) ==== Archive Corporation (800) 537 2248 Tech Support (800) 227 6296 ==== QUESTION: What is the telephone number for Quantum? ANSWER From: paladin@world.std.com (Thomas G Schlatter) ==== Quantum: BBS? (408) 434-1664 FAX (408) 943-0689 Tech support (408) 432-1100 ==== QUESTION: What is the telephone number for Seagate? ANSWER From: landis@sugs.tware.com (Hale Landis) ==== Here are the numbers for Seagate's Technical Support. SeaBOARD - Bulletin Board System available 24 hours. Use 8 data bits, no parity, 1 stop bit (8-N-1). USA/Canada 408-438-8771 9600 baud* England 44-62-847-8011 9600 baud* Germany 49-89-140-9331 2400 baud* Singapore 65-292-6973 9600 baud* Australia 61-2-756-2359 9600 baud* * - Maximum baud rate supported. SeaFAX 408-438-2620 Use a touch-tone phone to have information returned to you via FAX. Available 24 hours. Technical Support Fax 408-438-8137 FAX your questions or comments 24 hours. Responses are sent between 8:00AM and 5:00PM PST Monday through Friday. SeaFONE 408-438-8222 Provides recorded information 24 hours or talk to a technical specialist between 8:00AM to 5:00PM PST Monday through Friday. SeaTDD 408-438-5382 Using a Telecommunications Device for the Deaf, you can send questions or comments 24 hours or have a dialog with a technical support specialist between 8:00AM and 5:00PM PST Monday through Friday. ==== QUESTION: What is the telephone number and address of Conner Peripherals? ANSWER From: ekrieger@quasar.hacktic.nl (Eric Krieger) ==== CONNER PERIPHERALS, Incorporated WATTS LINE: 3081 Zanker Road PAY LINE: (408)456-4500 San Jose CA 95134 FAX LINE: BBS LINE: (408)456-4415 (V.32) CONNER (408)456-3200 ==== QUESTION: What is the address and telephone number of WANGTEK? ANSWER From: "Terry Kennedy, Operations Mgr" <uunet!spcvxa.spc.edu!TERRY> ==== Wangtek can be reached at: WANGTEK Incorporated 41 Moreland Road Simi Valley, CA 93065 (805) 583-5255 [voice] (805) 583-8249 [FAX] (805) 582-3370 [BBS] WANGTEK-Europe Unit 1A, Apollo House Calleva Industrial Park Aldermaston, Reading RG7 4QW England (44) 734-811463 [voice] (44) 734-816076 [FAX] 851-848135 [telex] ==== QUESTION: What is the number for NCR? ANSWER From: gkendall@ncr-mpd.FtCollinsCO.NCR.COM (Guy Kendall) ==== For data manuals for any NCR chips, please call 800-334-5454 or 719-630-3384. ==== QUESTION: what is FAST SCSI? ANSWER From: kev@hpcpbla.bri.hp.com (Kevin Jones) ==== There are 2 handshaking modes on the SCSI bus, used for transferring data: ASYNCHRONOUS and SYNCHRONOUS. ASYNCHRONOUS is a classic Req/Ack handshake. SYNCHRONOUS is "sort of" Req/Ack, only it allows you to issue multiple Req's before receiving Ack's. What this means in practice is that SYNCHRONOUS transfers are approx 3 times faster than ASYNCHRONOUS. SCSI1 allowed asynchronous transfers at up to 1.5 Mbytes/Sec and synchronous transfers at up to 5.0 Mbytes/Sec. SCSI2 had some of the timing margins "shaved" in order that faster handshaking could occur. The result is that asynchronous transfers can run at up to 3.0 Mbytes/Sec and synchronous transfers at up to 10.0 Mbytes/Sec. The term "FAST" is generally applied to a SCSI device which can do syncrhonous transfers at speeds in excess of 5.0 Mbytes/Sec. This term can only be applied to SCSI2 devices since SCSI1 didn't have the timing margins that allow for FAST transfers. ==== QUESTION: Where can I get SCSI documents? ANSWER From: kev@hpcpbla.bri.hp.com (Kevin Jones) and jmatrow@donald.WichitaKS.NCR.COM (John Matrow ==== The only literature that I'm aware of is: The SCSI specification: Available from: Global Engineering Documents 15 Inverness Way East Englewood Co 80112-5704 (800) 854-7179 SCSI-1: X3.131-1986 SCSI-2: X3.131-199x SCSI-3 X3T9.2/91-010R4 Working Draft (Global Engineering Documentation in Irvine, CA (714)261-1455??) SCSI-1: Doc # X3.131-1986 from ANSI, 1430 Broadway, NY, NY 10018 IN-DEPTH EXPLORATION OF SCSI can be obtained from Solution Technology, Attn: SCSI Publications, POB 104, Boulder Creek, CA 95006, (408)338-4285, FAX (408)338-4374 THE SCSI ENCYLOPEDIA and the SCSI BENCH REFERENCE can be obtained from ENDL Publishing, 14426 Black Walnut Ct., Saratoga, CA 95090, (408)867-6642, FAX (408)867-2115 SCSI: UNDERSTANDING THE SMALL COMPUTER SYSTEM INTERFACE was published by Prentice-Hall, ISBN 0-13-796855-8 ==== QUESTION: SCSI terminators should measure 136 ohms? ANSWER From: stevel@coos.dartmouth.edu (Steve Ligett) ==== Yes, that is what you should measure. Let's see how that is so. The terminator contains 18 220-ohm resistors from signals to termpower, and 18 330-ohm resistors from those signals to ground. I've drawn that below: termpower--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ | | | | | | | | | | | | | | | | | | 220 ohms-> R R R R R R R R R R R R R R R R R R | | | | | | | | | | | | | | | | | | signals -> o o o o o o o o o o o o o o o o o o | | | | | | | | | | | | | | | | | | 330 ohms-> R R R R R R R R R R R R R R R R R R | | | | | | | | | | | | | | | | | | ground --+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ When you measure from any one signal to termpower, you aren't measuring that resistor in isolation, you are measuring that resistor IN PARALLEL with the combination of the corresponding 330 ohm resistor plus 17 220+330 ohm resistor pairs in series. I've redrawn the schematic to make this easier to see: termpower--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ | | | | | | | | | | | | | | | | | | | R R R R R R R R R R R R R R R R R <- 220 ohms | | | | | | | | | | | | | | | | | | | o o o o o o o o o o o o o o o o o | | | | | | | | | | | | | | | | | | | R R R R R R R R R R R R R R R R R <- 330 ohms 220 ohms R | | | | | | | | | | | | | | | | | | +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+-- ground | | | R <-- 330 ohms | / signal -> o-/ <our resistor><--------- other stuff that's in parallel ----------> We're trying to measure that one resistor from a signal to termpower, but there's a ton of other stuff in parallel. The resistance of that "stuff" is 330 + 550/17 ohms (the 330 ohm resistor, in series with a parallel combination of 17 550 ohm resistors). The general formula for the equivalent of two resistances in parallel is r1*r2/(r1+r2). Whipping out my trusty spreadsheet, I find that the "stuff" has a resistance of about 362 ohms, and that in parallel with 220 ohms is about 137 ohms. ==== QUESTION: What are the pinouts for SCSI connectors? From: snively@scsi.Eng.Sun.COM (Bob Snively) ==== Originally dated May 23, 1990 The connector families described by the drawings have standard pin numberings which are described the same way by all vendors that I have encountered. The SCSI-2 specification identifies the standard numbering, using that convention. It happened to be documented by AMP, but all the vendors use the same convention. The following diagrams have the outline drawings of connector sockets at the bottom. This is really for reference only, because the connector sockets and plugs are both specified as to their numbering and usually are labeled. There are some minor problems in naming the microconnector conductor pairs, which I have corrected in the enclosed diagram. All the conductor pairs of the Mini-Micro (High Density) connector are in fact passed through on the cables. SCSI-2 defines the RSR (Reserved) lines as maybe ground or maybe open, but they are still passed through the cable. Most present standard SCSI devices will ground those lines. -------------------- microSCSI to SCSI Diagram --------------------------- SCSI Connector Pinouts _____________________________________ _____________________________________ | SCSI | | MINI | | | SCSI | | MINI | | | SIGNAL| DD-50P | MICRO | DD-50SA | | SIGNAL| DD-50P | MICRO | DD-50SA | ------------------------------------ ------------------------------------- | -DB(0)| 2 | 26 | 34 | | GND | 1 | 1 | 1 | | -DB(1)| 4 | 27 | 2 | | GND | 3 | 2 | 18 | | -DB(2)| 6 | 28 | 19 | | GND | 5 | 3 | 35 | | -DB(3)| 8 | 29 | 36 | | GND | 7 | 4 | 3 | | -DB(4)| 10 | 30 | 4 | | GND | 9 | 5 | 20 | | -DB(5)| 12 | 31 | 21 | | GND | 11 | 6 | 37 | | -DB(6)| 14 | 32 | 38 | | GND | 13 | 7 | 5 | | -DB(7)| 16 | 33 | 6 | | GND | 15 | 8 | 22 | | -DB(P)| 18 | 34 | 23 | | GND | 17 | 9 | 39 | | GND | 20 | 35 | 40 | | GND | 19 | 10 | 7 | | GND | 22 | 36 | 8 | | GND | 21 | 11 | 24 | | RSR | 24 | 37 | 25 | | RSR | 23 | 12 | 41 | |TERMPWR| 26 | 38 | 42 | | OPEN | 25 | 13 | 9 | | RSR | 28 | 39 | 10 | | RSR | 27 | 14 | 26 | | GND | 30 | 40 | 27 | | GND | 29 | 15 | 43 | | -ATN | 32 | 41 | 44 | | GND | 31 | 16 | 11 | | GND | 34 | 42 | 12 | | GND | 33 | 17 | 28 | | BSY | 36 | 43 | 29 | | GND | 35 | 18 | 45 | | -ACK | 38 | 44 | 46 | | GND | 37 | 19 | 13 | | -RST | 40 | 45 | 14 | | GND | 39 | 20 | 30 | | -MSG | 42 | 46 | 31 | | GND | 41 | 21 | 47 | | -SEL | 44 | 47 | 48 | | GND | 43 | 22 | 15 | | -C/D | 46 | 48 | 16 | | GND | 45 | 23 | 32 | | -REQ | 48 | 49 | 33 | | GND | 47 | 24 | 49 | | -I/O | 50 | 50 | 50 | | GND | 49 | 25 | 17 | ---------------------------------------------------------------------------- * NC = NOT CONNECTED CONNECTOR TYPES: DD-50SA ________________________ MINI-MICRO DD-50P | ------------------- | _____________________ ______________ |17 \o o o o o o o o o/1 | | _________________ | 49| o o o o o o |1 | 33 \ o o o o o o o /18 | |25\ o o o o o o o /1| 50| o o o o o o |2 | 50 \o o o o o o o/ 34 | | 50\o o o o o o o/26| --------------- | ------------- | | -------------- | -------------------------- ---------------------- (VIEWED FROM FACE OF CONNECTOR - USE VENDOR NUMBERING SYSTEM AS SPECIFIED) ==== QUESTION: what is the difference between SCSI-1 and SCSI-2? ANSWER From Dal Allen: ==== SCSI-1_versus_SCSI-2 In 1985, when the first SCSI standard was being finalized as an American National Standard, the X3T9.2 Task Group was approached by a group of manufacturers. The group wanted to increase the mandatory requirements of SCSI and to define further features for direct-access devices. Rather than delay the SCSI standard, X3T9.2 formed an ad hoc group to develop a working paper that was eventually called the Common Command Set (CCS). Many products were designed to this working paper. In parallel with the development of the CCS working paper, X3T9.2 sought permission to begin working on an enhanced SCSI standard, to be called SCSI-2. SCSI-2 would include the results of the CCS working paper, caching commands, performance enhancement features, and whatever else X3T9.2 deemed worthwhile. While SCSI-2 was to go beyond the original SCSI standard (now referred to as SCSI-1), it was to retain a high degree of compatibility with SCSI-1 devices. How is SCSI-2 different from SCSI-1? 1. Several options were removed from SCSI-1: a. Single initiator option was removed. b. Non-arbitrating Systems option was removed. c. Non-extended sense data option was removed. d. Reservation queuing option was removed. e. The read-only device command set was replaced by the CD-ROM command set. f. The alternative 1 shielded connector was dropped. 2. There are several new low-level requirements in SCSI-2: a. Parity must be implemented. b. Initiators must provide TERMPWR -- Targets may provide TERMPWR. c. The arbitration delay was extended to 2.4 us from 2.2 us. d. Message support is now required. 3. Many options significantly enhancing SCSI were added: a. Wide SCSI (up to 32 bits wide using a second cable) b. Fast SCSI (synchronous data transfers of up to 10 Mega-transfers per second -- up to 40 MegaBytes per second when combined with wide SCSI) c. Command queuing (up to 256 commands per initiator on each logical unit) d. High-density connector alternatives were added for both shielded and non- shielded connectors. e. Improved termination for single-ended buses (Alternative 2) f. Asynchronous event notification g. Extended contingent allegiance h. Terminate I/O Process messaging for time- critical process termination 4. New command sets were added to SCSI-2 including: a. CD-ROM (replaces read-only devices) b. Scanner devices c. Optical memory devices (provides for write-once, read-only, and erasable media) d. Medium changer devices e. Communications devices 5. All command sets were enhanced: a. Device Models were added b. Extended sense was expanded to add: + Additional sense codes + Additional sense code qualifiers + Field replaceable unit code + Sense key specific bytes c. INQUIRY DATA was expanded to add: + An implemented options byte + Vendor identification field + Product identification field + Product revision level field + Vital product data (more extensive product reporting) d. The MODE SELECT and MODE SENSE commands were paged for all device types e. The following commands were added for all device types: + CHANGE DEFINITION + LOG SELECT + LOG SENSE + READ BUFFER + WRITE BUFFER f. The COPY command definition was expanded to include information on how to handle inexact block sizes and to include an image copy option. g. The direct-access device command set was enhanced as follows: + The FORMAT UNIT command provides more control over defect management + Cache management was added: - LOCK/UNLOCK CACHE command - PREFETCH command - SYNCHRONIZE CACHE command - Force unit access bit - Disable page out bit + Several new commands were added: - READ DEFECT DATA - READ LONG - WRITE LONG - WRITE SAME + The sequential-access device command set was enhanced as follows: - Partitioned media concept was added: * LOCATE command * READ POSITION command - Several mode pages were added - Buffered mode 2 was added - An immediate bit was added to the WRITE FILEMARKS command + The printer device command set was enhanced as follows: - Several mode pages defined: * Disconnect/reconnect * Parallel printer * Serial printer * Printer options + The write-once (optical) device command set was enhanced by: - Several new commands were added: * MEDIUM SCAN * READ UPDATED BLOCK * UPDATE BLOCK - Twelve-byte command descriptor blocks were defined for several commands to accommodate larger transfer lengths. ============================================================================= The following article was written by Dal Allan of ENDL in April 1990. It was published nine months later in the January 1991 issue of "Computer Technology Review". While it appeared in the Tape Storage Technology Section of CTR, the article is general in nature and tape-specific. In spite of the less than timely publication, most of the information is still valid. It is reprinted here with the permission of the author. If you copy this article, please include this notice giving "Computer Technology Review" credit for first publication. ------------------------------------------------------------------------------ What's New in SCSI-2 Scuzzy is the pronunciation and SCSI (Small Computer System Interface) is the acronym, for the best known and most widely used ANSI (American National Standards Institute) interface. Despite use of the term "Small" in its name, everyone has to agree that Scuzzy is large - in use, in market impact, in influence, and unfortunately, in documentation. The standards effort that began with a 20-page specification in 1980 has grown to a 600 page extravaganza of technical information. Even before ANSI (American National Standards Institute) published the first run of SCSI as standards document in 1986, ASC (Accredited Standards Committee) X3T9.2 was hard at work on SCSI-2. No technical rationale can be offered as to why SCSI-1 ended and SCSI-2 began, or as to why SCSI-2 ended and SCSI-3 began. The justification is much more simple - you have to stop sometime and get a standard printed. Popular interfaces never stop evolving, adapting, and expanding to meet more uses than originally envisaged. Interfaces even live far beyond their technological lifespan. SMD (Storage Module Drive) has been called technically obsolete for 5 years but every year there are more megabytes shipped on the SMD interface than the year before. This will probably continue for another year or so before the high point is reached, and it will at least a decade before SMD is considered to be insignificant. If SCSI enhancements are cut off at an arbitrary point, what initiates the decision? Impatience is as good an answer as any. The committee and the market get sick of promises that the revision process will "end soon," and assert pressure to "do it now." The SCSI-3 effort is actively under way right now, and the workload of the committee seems to be no less than it was a year ago. What is pleasant, is that the political pressures have eased. There is a major difference between the standards for SCSI in 1986 and SCSI- 2 in 1990. The stated goal of compatibility between manufacturers had not been achieved in SCSI in 1986 due to a proliferation of undocumented "features." Each implementation was different enough that new software drivers had to be written for each device. OEMs defined variations in hardware that required custom development programs and unique microcode. Out of this diversity arose a cry for commonality that turned into CCS (Common Command Set), and became so popular that it took on an identity of its own. CCS defined the data structures of Mode Select and Mode Sense commands, defect management on the Format command and error recovery procedures. CCS succeeded because the goals were limited, the objectives clear and the time was right. CCS was the beginning of SCSI-2, but it was only for disks. Tape and optical disks suffered from diversity, and so it was that the first working group efforts on SCSI-2 were focused on tapes and optical disks. However, opening up a new standards effort is like lifting the lid on Pandora's Box - its hard to stay focused on a single task. SCSI-2 went far beyond extending and consolidating CCS for multiple device types. SCSI-2 represents three years of creative thought by some of the best minds in the business. Many of the new features will be useful only in advanced systems; a few will find their way into the average user's system. Some may never appear in any useful form and will atrophy, as did some original SCSI features like Extended Identify. Before beginning coverage of "what's new in SCSI-2," it might be well to list some of the things that aren't new. The silicon chips designed for SCSI are still usable. No new features were introduced which obsolete chips. The cause of silicon obsolescence has been rapid market shifts in integrating functions to provide higher performance. Similarly, initiators which were designed properly, according to SCSI in 1986, will successfully support SCSI-2 peripherals. However, it should be pointed out that not all the initiators sold over the last few years behaved according to the standard, and they can be "blown away "by SCSI-2 targets. The 1986 standard allows either initiators or targets to begin negotiation for synchronous transfers, and requires that both initiators and targets properly handle the sequence. A surprisingly large percentage of SCSI initiators will fail if the target begins negotiation. This has not been as much of a problem to date as it will become in the future, and you know as well as I do, that these non-compliant initiators are going to blame the SCSI-2 targets for being "incompatible." Quirks in the 1986 standard, like 4 bytes being transferred on Request Sense, even if the requested length was zero have been corrected in SCSI-2. Initiators which relied on this quirk instead of requesting 4 bytes will get into trouble with a SCSI-2 target. A sincere effort has been made to ensure that a 1986-compliant initiator does not fail or have problems with a SCSI-2 target. If problems occur, look for a non-compliant initiator before you blame the SCSI-2 standard. After that little lecture, let us turn to the features you will find in SCSI-2 which include: o Wide SCSI: SCSI may now transfer data at bus widths of 16 and 32 bits. Commands, status, messages and arbitration are still 8 bits, and the B-Cable has 68 pins for data bits. Cabling was a confusing issue in the closing days of SCSI-2, because the first project of SCSI-3 was the definition of a 16- bit wide P-Cable which supported 16-bit arbitration as well as 16-bit data transfers. Although SCSI-2 does not contain a definition of the P-Cable, it is quite possible that within the year, the P-Cable will be most popular non-SCSI-2 feature on SCSI-2 products. The market responds to what it wants, not the the arbitrary cutoffs of standards committees. o Fast SCSI: A 10 MHz transfer rate for SCSI came out of a joint effort with the IPI (Intelligent Peripheral Interface) committee in ASC X3T9.3. Fast SCSI achieves 10 Megabytes/second on the A-Cable and with wider data paths of 16- and 32-bits can rise to 20 Megabytes/second and even 40 Megabytes/second. However, by the time the market starts demanding 40 Megabytes/second it is likely that the effort to serialize the physical interface for SCSI-3 will attract high-performance SCSI users to the Fiber Channel. A word of caution. At this time the fast parameters cannot be met by the Single Ended electrical class, and is only suitable for Differential. One of the goals in SCSI-3 is to identify the improvements needed to achieve 10 MHz operation with Single Ended components. o Termination: The Single Ended electrical class depends on very tight termination tolerances, but the passive 132 ohm termination defined in 1986 is mismatched with the cable impedance (typically below 100 ohms). Although not a problem at low speeds when only a few devices are connected, reflections can cause errors when transfer rates increase and/or more devices are added. In SCSI-2, an active terminator has been defined which lowers termination to 110 ohms and is a major boost to system integrity. o Bus Arbitration, Parity and the Identify Message were options of SCSI, but are required in SCSI-2. All but the earliest and most primitive SCSI implementations had these features anyway, so SCSI-2 only legitimizes the de facto market choices. The Identify message has been enhanced to allow the target to execute processes, so that commands can be issued to the target and not just the LUNs. o Connectors: The tab and receptacle microconnectors chosen for SCSI-2 are available from several sources. A smaller connector was seen as essential for the shrinking form factor of disk drives and other peripherals. This selection was one of the most argued over and contentious decisions made during SCSI-2 development. o Rotational Position Locking: A rose by any other name, this feature defines synchronized spindles, so than an initiator can manage disk targets which have their spindles locked in a known relative position to each other. Synchronized disks do not all have to be at Index, they can be set to an offset in time relative to the master drive. By arraying banks of synchronized disks, faster transfer rates can be achieved. o Contingent Allegiance: This existed in SCSI-1, even though it was not defined, and is required to prevent the corruption of error sense data. Targets in the Contingent Allegiance state reject all commands from other initiators until the error status is cleared by the initiator that received the Check Condition when the error occurred. Deferred errors were a problem in the original SCSI but were not described. A deferred error occurs in buffered systems when the target advises Good Status when it accepts written data into a buffer. Some time later, if anything goes wrong when the buffer contents are being written to the media, you have a deferred error. o Extended Contingent Allegiance (ECA): This extends the utility of the Contingent Allegiance state for an indefinite period during which the initiator that received the error can perform advanced recovery algorithms. o Asynchronous Event Notification (AEN): This function compensates for a deficiency in the original SCSI which did not permit a target to advise the initiator of asynchronous events such as a cartridge being loaded into a tape drive. o Mandatory Messages: The list of mandated messages has grown: +----------------------+--------------------------+-------------------+ | Both | Target | Initiator | +----------------------+--------------------------+-------------------| | Identify | Abort | Disconnect | | | | | | Message Reject | No Operation | Restore Pointer | | | | | | Message Parity Error | Bus Device Reset | Save Data Pointer | | | | | | | Initiator Detected Error | | +----------------------+--------------------------+-------------------+ o Optional messages have been added to negotiate wide transfers and Tags to support command queueing. A last-minute inclusion in SCSI-2 was the ability to Terminate I/O and receive the residue information in Check Condition status (so that only the incomplete part of the command need be re-started by the initiator). o Command Queueing: In SCSI-1, initiators were limited to one command per LUN e.g. a disk drive. Now up to 256 commands can be outstanding to one LUN. The target is allowed to re-sequence the order of command execution to optimize seek motions. Queued commands require Tag messages which follow the Identify. o Disk Cacheing: Two control bits are used in the CDB (Command Descriptor Block) to control whether the cache is accessed on a Read or Write command, and some commands have been added to control pre-fetching and locking of data into the cache. Users do not have to change their software to take advantage of cacheing, however, as the Mode Select/Mode Sense Cache page allows parameters to be set which optimize the algorithms used in the target to maximize cache performance. Here is another area in which improvements have already been proposed in SCSI-3, and will turn up in SCSI-2 products shipping later this year. o Sense Keys and Sense Codes have been formalized and extended. A subscript byte to the Sense Code has been added to provide specifics on the type of error being reported. Although of little value to error recovery, the additional information about error causes is useful to the engineer who has to analyze failures in the field, and can be used by host systems as input to prognostic analysis to anticipate fault conditions. o Commands: Many old commands have been reworked and several new commands have been added. o Pages: Some method had to be found to pass parameters between host and target, and the technique used is known as pages. The concept was introduced in CCS and has been expanded mightily in SCSI-2. A number of new Common Commands have been added, and the opcode space for 10-byte CDBs has been doubled. o Change Definition allows a SCSI-2 initiator to instruct a SCSI-2 target to stop executing according to the 1986 standard, and provide advanced SCSI- 2 features. Most SCSI-2 targets will power on and operate according to the 1986 standard (so that there is no risk of "disturbing" the installed initiators, and will only begin operating in SCSI-2 mode, offering access to the advanced SCSI-2 capabilities, after being instructed to do so by the initiator using the Change Definition command. o The Mode Select and Mode Sense pages which describe parameters for operation have been greatly expanded, from practically nothing in 1986 to hundreds of items in SCSI-2. Whenever you hear of something being described as powerful and flexible tool, think complicated. Integrators are advised to be judicious in their selection of the pages they decide to support. o the Inquiry command now provides all sorts of interesting data about the target and its LUNs. Some of this is fixed by the standard, but the main benefit may be in the Vendor Unique data segregated into the special designation of Vital Product Data, which can be used by integrators as a tool to manage the system environment. o Select Log and Sense Log have been added so that the initiator can gather both historical (e.g. all Check Conditions) and statistical (e.g. number of soft errors requiring ECC) data from the target. o Diagnostic capabilities have been extended on the Read/Write Buffer and Read/Write Long commands. The ways in which the target can manage bad blocks in the user data space have been defined further and regulated to reduce inconsistencies in the 1986 standard. A companion capability to Read Defect Data permits the initiator to use a standard method to be advised of drive defect lists. o A new group of 12-byte command blocks has been defined for all optical devices to support the large volume sizes and potentially large transfer lengths. The Erase command has been added for rewritable optical disks so that areas on the media can be pre-erased for subsequent recording. Write Once disks need Media Scan, so that the user can find blank areas on the media. o New command sets have been added for Scanners, Medium Changers, and CD ROMs. All of this technical detail can get boring, so how about some "goodies" in SCSI-2 which benefit the common man and help the struggling engineer? First, and probably the best feature in SCSI-2 is that the document has been alphabetized. No longer do you have to embark on a hunt for the Read command because you cannot remember the opcode. In the 1986 standard, everything was in numeric sequence, and the only engineers who could find things easily were the microprogrammers who had memorized all the message and opcode tables. Now, ordinary people can find the Read command because it is in alphabetic sequence. This reorganization may sound like a small matter but it wasn't, it required a considerable amount of effort on the part of the SCSI-2 editors. It was well worth it. Another boon is the introduction for each device class of models which describe the device class characteristics. The tape model was the most needed, because various tape devices use the same acronym but with different meanings or different acronyms for the same meaning. The SCSI-2 tape model defines the terms used by SCSI-2, and how they correspond to the acronyms of the different tapes. For example, on a 9-track reel, End of Tape is a warning, and there is sufficient media beyond the reflective spot to record more data and a trailer. Not so on a 1/4" tape cartridge, End of Tape means out of media and no more data can be written. This sort of difference in terms causes nightmares for standardization efforts. So there it is, a summary of what is in SCSI-2. Its not scary, although it is daunting to imagine plowing through a 600-page document. Time for a commercial here. The "SCSI Bench Reference" available from ENDL Publications (408-867-6642), is a compaction of the standard. It takes the 10% of SCSI-2 which is constantly referenced by any implementor, and puts it in an easy- to-use reference format in a small handbook. The author is Jeff Stai, one of the earliest engineers to become involved with SCSI implementation, and a significant contributor to the development of both the 1986 standard and SCSI-2. SCSI-2 is not yet published as a standard, but it will be available later this year. Until then, the latest revision can be purchased from Global Engineering (800-854-7179). Biography Consultant and analyst I. Dal Allan is the founder of ENDL and publisher of the ENDL Letter and the "SCSI Bench Reference." A pioneer and activist in the development and use of standard interfaces, he is Vice Chairman of ASC X3T9.2 (SCSI) and Chairman of the SCSI-2 Common Access Method Committee. ==== QUESTION: Is SYNCHRONOUS faster than ASYNCHRONOUS? QUESTION: Is the 53C90 Faster than spec? From: kstewart@ncr-mpd.FtCollins.NCR.COM (Ken Stewart) ==== I've seen a few comments about our 54C90 being faster than spec. While I doubt the author was really complaining (I got twice as much as I paid for--sure makes me mad ;) I'd like to explain the situation. Along the way, I'll also show that asynchronous is faster on short cables, while synchronous is faster on long cables. The cross-over point occurs somewhere around six feet--assuming that you have our 53C90 family devices at both ends of the cable. The reason has to do with the propagation delay of the cable; the turn around time of the silicon; and the interlocked nature of the asynchronous handshake. 1) We have measured propagation delays from various cables and found an average of 1.7 nanoseconds per foot, which is roughly 5.25 ns per meter. 2) The turn-around time is the amount of time the SCSI chip takes to change an output in response to an input. If REQ is an input then ACK is an output. Or if ACK is an input then REQ is an output. Typical turn-around time for the 53C90 is 40 nanoseconds. 3) The asynchronous transfer uses an interlocked handshake where a device cannot do the next thing until it receives positive acknowledgment that the other device received the last thing. First REQ goes true /* driven by Target */ then ACK is permitted to go true /* driven by Initiator */ then REQ is permitted to go false then ACK is permitted to go false Thus we have four "edges" propagating down the cable plus 4 turn-around delays. Asynchronous transfer requires 55 ns setup and no hold time (paragraph in 5.1.5.1 in SCSI-1 or SCSI-2) which gives an upper speed limit around 18 MB/s. A detailed analysis (assuming 53C90 family) shows that the setup time subtracts out. This is mostly because we are running at one-third the max rate, but also because setup for the next byte can begin anytime after ACK is received true or REQ is received false, depending on who is receiving. You can either take my word for it or draw the waveforms yourself. Thus, the asynchronous transfer reduces to: (4 * 1.7 * 1) + (4 * 40ns) = 167 ns /* 1 foot cable */ = 6 MB/s (4 * 5.25 * 6) + (4 * 40ns) = 286 ns /* 6 meter cable */ = 3.5 MB/s (4 * 5.25 * 25) + (4 * 40ns) = 685 ns /* 25 meter cable */ = 1.5 MB/s note: cables longer than 6 meters require external differential transceivers which add delay and degrade the performance even more than indicated here. Our simulations say that under very best conditions (fast silicon, low temperature, high voltage, zero length cable) we can expect more than 8 MB/s asynchronously. In the lab, I routinely measure 5 MB/s on 8 foot cables. So, if you were writing the data manual for this, how would YOU spec it? The framers of the SCSI spec threw in synchronous mode to boost the performance on long cables. In synchronous mode, the sending device is permitted to send the next byte without receiving acknowledgment that the receiver actually received the last byte. Kind of a ship and pray method. The acknowledgment is required to come back sometime, but we just don't have to wait for it (handwave the offset stuff and the ending boundary conditions). In this mode any external transceivers add a time shift, but not a delay. So if you negotiate for 5 MB/s, you get 5MB/s regardless how long the cable is and regardless whether you are single-ended or differential. But you can't go faster than 5.5 MB/s, except in SCSI-2. Synchronous mode does have a hold time (unlike asynch) but again, setup and hold times subtract out. In SCSI-1 synchronous mode, the speed limit comes from the combined ASSERTION PERIOD + NEGATION PERIOD which is 90ns + 90ns = 180ns = 5.5 MB/s. Our 53C90 family doesn't quite hit the max, but we do guarentee 5.0 MB/s. In SCSI-2, anything above 5.0 MB/s is considered to be FAST. Here the maximum transfer rate is explicitly limited to 100 ns or 10MB/s; you don't have to read between the lines to deduce it. Interesting tid-bit: given a SCSI-2 FAST period of 100 ns and a cable delay of 131 ns on a 25 meter cable, you can actually stack 1.31 bytes in the 8-bit cable. In FAST and WIDE SCSI you can stack 5.24 bytes in this copper FIFO. Hummm... ==== QUESTION: What are the jumpers on my Conner drive? ANSWER From: ekrieger@quasar.hacktic.nl (Eric Krieger) ==== QUICK INSTALLATION GUIDE SCSI Most SCSI host adapters are compatible with Conner drives. Software drivers and installation instructions are provided with the host adapter. The drives are shipped with SCSI ID set to 7. To select a different ID refer to the following: Table A Table B ID E-1 E-2 E-3 ID E2 E3 E4 0 out out out 0 out out out 1 in out out 1 in out out 2 out in out 2 out in out 3 in in out 3 in in out 4 out out in 4 out out in 5 in out in 5 in out in 6 out in in 6 out in in 7 in in in 7 in in in Parity is always ENABLED on the CP3200,CP30060,CP30080,CP30100. All other models, jumper E-4 to disable parity. SCSI drive parameters: Model Hds Cyl Sec Table LED CP2020 2 642 32 A n/a CP340 4 788 26 B 1 CP3020 2 622 33 A 1 CP3040 2 1026 40 A 1 CP3180 6 832 33 A 1 CP3100 8 776 33 A 1 CP30060 2 1524 39 A 2 CP30080 4 1053 39 A 2 CP30100 4 1522 39 A 2 CP30200 4 2119 49 A 2 CP3200 8 1366 38 A 2 CP3360 8 1806 49 A 2 CP3540 12 1806 49 A 2 LED 1 LED 2 J-4 Pin 1 = + J-1 Pin 3 = + Pin 2 = - Pin 4 = - ==== QUESTION: What are the jumpers for my Wangtek 5150 drive? ANSWER From: "Terry Kennedy, Operations Mgr" <uunet!spcvxa.spc.edu!TERRY> ==== First, the disclaimer: This is not an official representation of Wangtek or of my employer. This is info I've discovered by reading publicly avail- able reference material. When changing jumpers, always observe proper anti- static precautions and be sure you have the current configuration written down so you have a known starting point. Ok. Here's the complete scoop on Wangtek 5150ES drives: The current part number for a "generic" 5150ES is: 33685-201 (black faceplate) 33685-202 (beige faceplate) These are referred to as the "ACA version" of the drive. There are _many_ other part numbers for 5150ES drives. If you have one that isn't one of the above, it doesn't mean you have an old or an out of rev drive, it just means its a special version created for a distributor or OEM, or with different default jumper settings. You can order the Wangtek 5150ES OEM Manual from Wangtek. It is part number 63045-001 Revision D. There are 5 possible logic boards. Here are the jumper options for each: Logic assembly #33678 --------------------- (J10) 0 - SCSI unit LSB 1 - SCSI unit 2 - SCSI unit MSB K - not documented J32 - Diagnostic test connector, default is not installed E1, F1 - SCSI termination power. E1 in = power from drive and to cable, E1 out - power from cable. F1 = terminator power fuse, 1.5A FB. Default is IN. E2 - Chassis ground. E2 in jumpers logic to chassis ground. E2 out isolates through a .33 uFD capacitor. Default is IN. E5 - Master oscillator enable. Test only. Must be IN. E20 - Factory test. Must be OUT. RP1, RP2, RP3 - SIP terminators. Default is IN, remove for no termination. Logic assembly #30559 --------------------- HDR1 - Factory testing. Setting depends on drive. Don't touch. HDR2 - Factory testing. Defaults are pins 15-16, 17-18, 19-20. Don't touch. HDR3 pin 1 - A-B enables buffered mode. B-C disables. Can be overridden by SCSI Mode Select. HDR3 pin 2, 3 - Default data format. Set to B-C for a 5150ES. HDR3 pin 4 - parity enable. A-B enables, B-C disables. (J10) 0 - SCSI unit LSB 1 - SCSI unit 2 - SCSI unit MSB K - not documented E1 - SCSI termination power. E1 in = power from drive and to cable, E1 out - power from cable. E2 - Chassis ground. E2 in jumpers logic to chassis ground. E2 out isolates through a .33 uFD capacitor. Default is IN. E3 - Master oscillator enable. Test only. Must be IN. E4 - Write test mode. Test only. Must be OUT. E5 - Write oscillator enable. Test only. Must be IN. E6 - Disable HDR2. Test only. Must be IN. E7 - Microcontroller clock select. In for a 5150ES. E8 - Write precomp select. Set on a per-drive basis. Don't touch. E9 - RAM size. Don't touch. E10 - Erase frequency. Don't touch. RP2, RP3 - DIP and SIP terminators. Default is IN, remove for no termination. Logic assembly #30600 --------------------- HDR1 - Factory testing. Setting depends on drive. Don't touch. HDR2 - Write precomp select. Set on a per-drive basis. Don't touch. HDR3 pin 1, 2, 3 - SCSI device address. 1 is LSB, 3 is MSB. A-B=1, B-C=0 HDR3 pin 4 - Parity enable. IA-B is enabled. HDR3 pin 5, 6 - Default data format. B-C for a 5150ES. HDR3 pin 7 - Buffered mode select. A-B is enabled. HDR3 pin 8 - Reserved. Must be OUT. HDR4 - Write frequency select. Don't touch. E1 - SCSI termination power. E1 in = power from drive and to cable, E1 out - power from cable. E2 - Chassis ground. E2 in jumpers logic to chassis ground. E2 out isolates through a .33 uFD capacitor. Default is IN. E3 - Hard/soft reset. IN enables hard reset. E4 - Write precomp select. Don't touch. E5 - Clock speed. Don't touch. E6 - Tape hole test. Don't touch. Logic assembly #30552 --------------------- HDR1 - Factory testing. Setting depends on drive. Don't touch. HDR2 - Write precomp select. Set on a per-drive basis. Don't touch. HDR3 pin 1, 2, 3 - SCSI device address. 1 is LSB, 3 is MSB. [Note - HDR3 pins 1-3 are duplicated at another location on the board] HDR3 pin 4 - Parity enable. IN is enabled. HDR3 pin 5, 6, 7, 8 - Default data format. 5,5 B-C, 7-8 A-B for a 5150ES. HDR4 - Write frequency select. Don't touch. E1 - SCSI termination power. E1 in = power from drive and to cable, E1 out - power from cable. E2 - Chassis ground. E2 in jumpers logic to chassis ground. E2 out isolates through a .33 uFD capacitor. Default is IN. E3 - Hard/soft reset. IN enables hard reset. E4 - Write precomp select. Don't touch. E5 - Clock speed. Don't touch. E6 - Tape hole test. Don't touch. Logic assembly #30427 --------------------- HDR1 - Factory testing. Setting depends on drive. Don't touch. HDR2 - Write precomp select. Set on a per-drive basis. Don't touch. HDR3 pin 1, 2, 3 - SCSI device address. 1 is LSB, 3 is MSB. A-B=1, B-C=0 HDR3 pin 4 - Parity enable. IA-B is enabled. HDR3 pin 5, 6, 7, 8 - Default data format. 5,5 B-C, 7-8 A-B for a 5150ES. E1, E3 - Factory test. Must be IN. E2 - SCSI termination power. E2 in = power from drive and to cable, E2 out - power from cable. E4 - Chassis ground. E4 in jumpers logic to chassis ground. E4 out isolates through a .33 uFD capacitor. Default is IN. Firmware - There are many flavors of firmware. I have seen the following parts: 24115-xxx 24144-xxx 21158-xxx the -xxx suffix changes as the firmware is updated. According to the folks I spoke to at Wangtek, the standard firmware is the 21158. The latest version as of this writing is 21158-007. All of these will work with the Adaptec and GTAK. The firmware options (as returned by a SCSI Identify) are on the end of the product string, which is "WANGTEK 5150ES SCSI ES41C560 AFD QFA STD" for the 21158-007 firmware. The 3-letter codes have the following meaning: AFD - Automatic Format Detection - the drive will recognize the format (such as QIC-24, QIC-120, or QIC-150) that the tape was written in. QFA - Quick File Access - the ability to rapidly locate a tape block, and to implement the "position to block" and "report block" SCSI commands. This is compatible with the Tandberg implementation. STD - Standard feature set. ==== QUESTION: What is CAM? ANSWER From: ctjones@bnr.ca (Clifton Jones) ==== Common Access Method. It is a proposed ANSI standard to make it easier to program SCSI applications by encapsulating the SCSI functions into a standardized calling convention. ANSWER From: landis@sugs.tware.com (Hale Landis) ==== You may be able to get the CAM spec(s) from the SCSI BBS ==== QUESTION: What is FPT (Termination)? ANSWER From: jvincent@bnr.ca (John Vincent) ==== FPT is actually really simple, I wish I had thought of it. What it does is use diode clamps to eliminate over and undershoot. The "trick" is that instead of clamping to +5 and GND they clamp to the output of two regulated voltages. This allows the clamping diodes to turn on earlier and is therefore better at eliminating overshoot and undershoot. The block diagram for a FPTed signal is below. The resistor value is probably in the 120 to 130 ohm range. The actual output voltages of the regulators may not be exaclty as I have shown them but ideally they are matched to the diode characteristics so that conduction occurs when the signal voltage is greater than 3.0 V or less than 0.5 V. +--------------- TERMPWR | ____|____ | | | Vreg 1 |-------*-------------------------*--------------- 3.? V |________| | | | | | | | \ +------------* / pullup resistor | | \ | | / | ____|___ | | | | | | | Vreg 2 |----------*----------|--------------- 3.0 V | |________| | | | --+-- | | / \ | +-----------+ /___\ | | | | | | | terminated | *----------*------------- signal | | | | | --+-- | / \ | /___\ | | ___|____ | | | | | Vreg 3 |----------*------------------------- 1.0 V (?) |________| ==== QUESTION: What is Active Termination? ANSWER From: eric@telebit.com (Eric Smith) and brent@auspex.com (Brent R. Largent) ==== An active terminator actually has one or more voltage regulators to produce the termination voltage, rather than using resistor voltage dividers. This is a passive terminator: TERMPWR ------/\/\/\/------+------/\/\/\/----- GND | | SCSI signal Notice that the termination voltage is varies with the voltage on the TERMPWR line. One voltage divider (two resistors) is used for each SCSI signal. An active terminator looks more like this (supply filter caps omitted): +-----------+ TERMPWR -----| in out |------+------/\/\/\/-------SCSI signal | gnd | | +-----------+ | | +------/\/\/\/-------SCSI signal | | GND ---------------+ | +------/\/\/\/-------SCSI signal | etc. Assuming that the TERMPWR voltage doesn't drop below the desired termination voltage (plus the regulator's minimum drop), the SCSI signals will always be terminated to the correct voltage level. Several vendors have started making SCSI active terminator chips, which contain the regulator and the resistors including Dallas Semiconductor, Unitrode Integerated Circuits and Motorola ==== QUESTION: Why Is Active Termination Better? ANSWER brent@auspex.com (Brent R. Largent) ==== Typical pasive terminators (resistors) fluctuate directly in relation to the TERM Power Voltage. Usually terminating resistors will suffice over short distances, like 2-3 feet, but for longer distances active termination is a real advantage. It reduces noise. Active Termination provide numerous advantages: - A logic bit can disconnect the termination - Provides Negative Clamping on all signal lines - Regulated termination voltage - SCSI-2 spec recommends active termination on both ends of the scsi cable. - Improved Resistance tolerences (from 1% to about 3%) ==== End. ====